In the AAC production line, this machine is used in the pouring and pre-curing section during slurry discharge from the mixer into the mould. Its function is to remove bubbles generated or carried during the pouring process so that the slurry condition in the mould can be improved before the next st...

The AAC side plate is as a necessary part for the AAC production line. It is used through the whole production process, including the pouring section, pre-curing section, cutting section, autoclaving section and finished products packing section. It works together with the mould and mould cart to ca...

The slurry and powder material scale system is used for the weight batching process in the AAC line. Sand slurry and waste slurry are measured by electronic scale, while cement and lime are measured by powder scale according to the proportion requirement. It serves as both a slurry weight scale and ...

This equipment is a fully automatic high-speed oiling machine, model GS-1. It can automatically identify the mould box, position it accurately and apply a small amount of mould release oil to the inner surfaces of the mould box. The equipment information emphasizes unattended operation and the centr...

The AAC mould is used in the pouring and pre-curing section as the container and carrying base for the slurry before demoulding and later transfer. The suitable type and quantity depend on the target annual production capacity. It also notes that the mould consists of steel channel and steel plate, ...

The up-and-down pouring device is as a key unit of the AAC block pouring machine. It comprises a pouring nozzle, lifting arm and air compressor cylinder, and is mounted below the pouring mixer while being connected with the PLC control system. It is positioned directly at the discharge point from th...

The pouring ferry push cart in the batching and pouring section of the AAC production line. It is composed of a working station, friction wheel or hooking and pushing mechanism, walking wheel and positioning device. The product description focuses on cross movement, positioning and alignment with ra...

The pre-curing cart as a unit used to convey the mould after pouring to the pre-curing room, and then convey the pre-cured mould to be cut. It explains that the mould cart to be transferred is sent from the ground track to the ferry cart through friction wheels, and that after alignment with the rec...

The horizontal cutting machine is used in the AAC cutting section to divide the green cake into layers after side cutting. It is arranged in the cutting line as a key cutting unit for forming the required product thickness and supporting the next cutting and transfer steps.

The vacuum suction hood is used in the AAC cutting section to clean waste generated during production. It is mounted on the vertical cutting machine or the hand-hole making machine so that waste can be collected during cutting and related processing.

The cutting cart is used around the AAC cutting station to convey the green cake and side plate from the turning hoist to the tilting table. It is a transfer unit in the cutting section that supports cake movement and section rhythm.

The tongue groove station is used in the AAC cutting section for side processing of the cake after transfer to the tongue-and-groove area. It is used for AAC block and panel production and is especially necessary and critical in AAC panel production.

The tilting table is used in the AAC cutting section to receive the green cake and side plate after turning and to support the following cutting and cleaning operations. It is part of the transfer and positioning sequence around the cutting station.

The tilting hoister is used in the AAC cutting section to grasp the mould and rotate it about 90 degrees for cutting preparation. During this operation, it also separates the empty mould base from the cake-and-side-wall combination so that mould components can return to the mould circulation route.

The top and bottom cleaning system is used in the AAC cutting section for automatic bottom or top peeling of the green body after cutting. It is used together with the tilting table to separate waste generated during cutting and recycle it into waste slurry.

The vertical cutting machine is used in the AAC cutting section for cross cutting after horizontal cutting. It is one of the core equipment in the cutting station and is used to cut the cake vertically according to the required value.

The tongue and groove milling device is used in the AAC cutting section for profile processing after the main cutting sequence. It can be used for both AAC block and panel production and is especially necessary and critical in panel production.

The green cake separator is used in the AAC cutting section to separate the cut green cake before autoclaving. It automatically adjusts the separating support position according to product specifications to complete the separating of green cake.